Controlling an led matrix using a single button using Morse code - a basic example for minimal communication channel

ADVERTISEMENT

Morse code is a simple way to communicate using just two symbols. A short one and a long one. This can be helpful in many ways. 

Morse code 

Here is simple weekend project using an 8x8 led matrix and and an arduino uno (atmega 328). In this project, i used a single button to output any character or short messages from the led matrix.

This project is very simple and wiring is simple (see the sketch below). Connect an led to pin 13 (or just use the on-board led) and an input key (push button) to pin 7. A max7219 led matrix is connected to pin 8,9,10 on the arduino. 

led matrix with Morse control

It is basically using a nice library by raronoff which can encode and decode morse code. In addition, if you are using max7219 module, a maxmatrix library is also needed

See the video below for a short demo and the arduino code is given after that. The potential of this circuit is more than this. Input key can be replaced with various other inputs than a mere push button. It could be a delicate switch and couple of circuitry to track breath air, chest movements, eye lids movements etc

/*
  A simple single key control of max7219, 8 X 8 led matrix using morse code          
  Credits raronoff (morse encoder) : http://raronoff.wordpress.com/2010/12/16/morse-endecoder/
  Details at http://blog.riyas.org

WIRING DETAILS
=============

Arduino PIN 13 to an led (blue) via 330 ohm resister
Arduino pin 7 connected to push button swith, the other end is grounded via 330 ohm resistor
PIN 8 to  DIN pin of MAX7219 module
PIN 9 to CS pin of MAX7219 module
PIN 10 to  CLK pin of MAX7219 module
*/

#include <avr/pgmspace.h>
#include <MorseEnDecoder.h>
#include <MaxMatrix.h>


PROGMEM prog_uchar CH[] = {
3, 8, B00000000, B00000000, B00000000, B00000000, B00000000, // space
1, 8, B01011111, B00000000, B00000000, B00000000, B00000000, // !
3, 8, B00000011, B00000000, B00000011, B00000000, B00000000, // "
5, 8, B00010100, B00111110, B00010100, B00111110, B00010100, // #
4, 8, B00100100, B01101010, B00101011, B00010010, B00000000, // $
5, 8, B01100011, B00010011, B00001000, B01100100, B01100011, // %
5, 8, B00110110, B01001001, B01010110, B00100000, B01010000, // &
1, 8, B00000011, B00000000, B00000000, B00000000, B00000000, // '
3, 8, B00011100, B00100010, B01000001, B00000000, B00000000, // (
3, 8, B01000001, B00100010, B00011100, B00000000, B00000000, // )
5, 8, B00101000, B00011000, B00001110, B00011000, B00101000, // *
5, 8, B00001000, B00001000, B00111110, B00001000, B00001000, // +
2, 8, B10110000, B01110000, B00000000, B00000000, B00000000, // ,
4, 8, B00001000, B00001000, B00001000, B00001000, B00000000, // -
2, 8, B01100000, B01100000, B00000000, B00000000, B00000000, // .
4, 8, B01100000, B00011000, B00000110, B00000001, B00000000, // /
4, 8, B00111110, B01000001, B01000001, B00111110, B00000000, // 0
3, 8, B01000010, B01111111, B01000000, B00000000, B00000000, // 1
4, 8, B01100010, B01010001, B01001001, B01000110, B00000000, // 2
4, 8, B00100010, B01000001, B01001001, B00110110, B00000000, // 3
4, 8, B00011000, B00010100, B00010010, B01111111, B00000000, // 4
4, 8, B00100111, B01000101, B01000101, B00111001, B00000000, // 5
4, 8, B00111110, B01001001, B01001001, B00110000, B00000000, // 6
4, 8, B01100001, B00010001, B00001001, B00000111, B00000000, // 7
4, 8, B00110110, B01001001, B01001001, B00110110, B00000000, // 8
4, 8, B00000110, B01001001, B01001001, B00111110, B00000000, // 9
2, 8, B01010000, B00000000, B00000000, B00000000, B00000000, // :
2, 8, B10000000, B01010000, B00000000, B00000000, B00000000, // ;
3, 8, B00010000, B00101000, B01000100, B00000000, B00000000, // <
3, 8, B00010100, B00010100, B00010100, B00000000, B00000000, // =
3, 8, B01000100, B00101000, B00010000, B00000000, B00000000, // >
4, 8, B00000010, B01011001, B00001001, B00000110, B00000000, // ?
5, 8, B00111110, B01001001, B01010101, B01011101, B00001110, // @
4, 8, B01111110, B00010001, B00010001, B01111110, B00000000, // A
4, 8, B01111111, B01001001, B01001001, B00110110, B00000000, // B
4, 8, B00111110, B01000001, B01000001, B00100010, B00000000, // C
4, 8, B01111111, B01000001, B01000001, B00111110, B00000000, // D
4, 8, B01111111, B01001001, B01001001, B01000001, B00000000, // E
4, 8, B01111111, B00001001, B00001001, B00000001, B00000000, // F
4, 8, B00111110, B01000001, B01001001, B01111010, B00000000, // G
4, 8, B01111111, B00001000, B00001000, B01111111, B00000000, // H
3, 8, B01000001, B01111111, B01000001, B00000000, B00000000, // I
4, 8, B00110000, B01000000, B01000001, B00111111, B00000000, // J
4, 8, B01111111, B00001000, B00010100, B01100011, B00000000, // K
4, 8, B01111111, B01000000, B01000000, B01000000, B00000000, // L
5, 8, B01111111, B00000010, B00001100, B00000010, B01111111, // M
5, 8, B01111111, B00000100, B00001000, B00010000, B01111111, // N
4, 8, B00111110, B01000001, B01000001, B00111110, B00000000, // O
4, 8, B01111111, B00001001, B00001001, B00000110, B00000000, // P
4, 8, B00111110, B01000001, B01000001, B10111110, B00000000, // Q
4, 8, B01111111, B00001001, B00001001, B01110110, B00000000, // R
4, 8, B01000110, B01001001, B01001001, B00110010, B00000000, // S
5, 8, B00000001, B00000001, B01111111, B00000001, B00000001, // T
4, 8, B00111111, B01000000, B01000000, B00111111, B00000000, // U
5, 8, B00001111, B00110000, B01000000, B00110000, B00001111, // V
5, 8, B00111111, B01000000, B00111000, B01000000, B00111111, // W
5, 8, B01100011, B00010100, B00001000, B00010100, B01100011, // X
5, 8, B00000111, B00001000, B01110000, B00001000, B00000111, // Y
4, 8, B01100001, B01010001, B01001001, B01000111, B00000000, // Z
2, 8, B01111111, B01000001, B00000000, B00000000, B00000000, // [
4, 8, B00000001, B00000110, B00011000, B01100000, B00000000, // \ backslash
2, 8, B01000001, B01111111, B00000000, B00000000, B00000000, // ]
3, 8, B00000010, B00000001, B00000010, B00000000, B00000000, // hat
4, 8, B01000000, B01000000, B01000000, B01000000, B00000000, // _
2, 8, B00000001, B00000010, B00000000, B00000000, B00000000, // `
4, 8, B00100000, B01010100, B01010100, B01111000, B00000000, // a
4, 8, B01111111, B01000100, B01000100, B00111000, B00000000, // b
4, 8, B00111000, B01000100, B01000100, B00101000, B00000000, // c
4, 8, B00111000, B01000100, B01000100, B01111111, B00000000, // d
4, 8, B00111000, B01010100, B01010100, B00011000, B00000000, // e
3, 8, B00000100, B01111110, B00000101, B00000000, B00000000, // f
4, 8, B10011000, B10100100, B10100100, B01111000, B00000000, // g
4, 8, B01111111, B00000100, B00000100, B01111000, B00000000, // h
3, 8, B01000100, B01111101, B01000000, B00000000, B00000000, // i
4, 8, B01000000, B10000000, B10000100, B01111101, B00000000, // j
4, 8, B01111111, B00010000, B00101000, B01000100, B00000000, // k
3, 8, B01000001, B01111111, B01000000, B00000000, B00000000, // l
5, 8, B01111100, B00000100, B01111100, B00000100, B01111000, // m
4, 8, B01111100, B00000100, B00000100, B01111000, B00000000, // n
4, 8, B00111000, B01000100, B01000100, B00111000, B00000000, // o
4, 8, B11111100, B00100100, B00100100, B00011000, B00000000, // p
4, 8, B00011000, B00100100, B00100100, B11111100, B00000000, // q
4, 8, B01111100, B00001000, B00000100, B00000100, B00000000, // r
4, 8, B01001000, B01010100, B01010100, B00100100, B00000000, // s
3, 8, B00000100, B00111111, B01000100, B00000000, B00000000, // t
4, 8, B00111100, B01000000, B01000000, B01111100, B00000000, // u
5, 8, B00011100, B00100000, B01000000, B00100000, B00011100, // v
5, 8, B00111100, B01000000, B00111100, B01000000, B00111100, // w
5, 8, B01000100, B00101000, B00010000, B00101000, B01000100, // x
4, 8, B10011100, B10100000, B10100000, B01111100, B00000000, // y
3, 8, B01100100, B01010100, B01001100, B00000000, B00000000, // z
3, 8, B00001000, B00110110, B01000001, B00000000, B00000000, // {
1, 8, B01111111, B00000000, B00000000, B00000000, B00000000, // |
3, 8, B01000001, B00110110, B00001000, B00000000, B00000000, // }
4, 8, B00001000, B00000100, B00001000, B00000100, B00000000, // ~
};

int data = 8;    // DIN pin of MAX7219 module
int load = 9;    // CS pin of MAX7219 module
int clock = 10;  // CLK pin of MAX7219 module

int maxInUse = 1;    //change this variable to set how many MAX7219's you'll use

MaxMatrix m(data, load, clock, maxInUse); // define module

byte buffer[10]; //store morse temp

// Pin mappings
const byte morseInPin = 7;      
const byte morseOutPin = 13;

// Instantiate Morse objects
morseDecoder morseInput(morseInPin, MORSE_KEYER, MORSE_ACTIVE_LOW);
morseEncoder morseOutput(morseOutPin);

// Variables dealing with formatting the output somewhat
// by inserting CR's (carriage returns)
long lastTransmissionTime;
long currentTime;
boolean transmissionEnded = true; // Flag to mark old transmission is finished

// Minimum transmission pause time to insert carriage returns (CR)
// Adjust depending on Morse speed. IE 13 wpm = 646 ms between words (no CR).
const long transmissionPaused   = 1000; // Suitable for 13 wpm?


void setup()
{
  Serial.begin(9600);
  m.init(); // module initialize
  m.setIntensity(0); // dot matix intensity 0-15
  Serial.println("Led Control with morse");
  
  // Setting Morse speed in wpm - words per minute
  // If not set, 13 wpm is default anyway
  morseInput.setspeed(10);
  morseOutput.setspeed(10);
  
  lastTransmissionTime = (long)millis();
}



void loop()
{
  currentTime = (long)millis();
  
  // Needs to call these once per loop
  morseInput.decode();
  morseOutput.encode();

  // SEND MORSE (OUTPUT)
  // Encode and send text received from the serial port (serial monitor)
  if (Serial.available() && morseOutput.available())
  {
    // Get character from serial and send as Morse code
    char sendMorse = Serial.read();
    morseOutput.write(sendMorse);
    
    // Not strictly needed, but used to get morseSignalString before it is destroyed
    // (E.g. for morse training purposes)
    morseOutput.encode();

    // Also write sent character + Morse code to serial port/monitor
    Serial.write(' ');
    Serial.write(sendMorse);
    // Morse code in morseSignalString is now backwards
    for (int i=morseOutput.morseSignals; i>0; i--)
    {
      Serial.write(morseOutput.morseSignalString[i-1]);
    }
  }


  // RECEIVE MORSE (INPUT)
  // If a character is decoded from the input, write it to serial port
  if (morseInput.available())
  {
    // Get decoded Morse code character and write it to serial port/monitor
    char receivedMorse = morseInput.read();
    Serial.print(receivedMorse);
    printString(receivedMorse); // output the charecter to led matrix    
    // A little error checking    
    if (receivedMorse == '#') Serial.println("< ERROR:too many morse signals! >");
  }


  // Local Morse code feedback from input if not sending Morse simultaneously
  if (morseOutput.available()) digitalWrite(morseOutPin, morseInput.morseSignalState);


  // Check if ongoing transmission (not yet transmission pause)
  if (!morseOutput.available() || morseInput.morseSignalState == true)
  {
    // reset last transmission timer and flag
    lastTransmissionTime = currentTime;
    transmissionEnded = false;
  }

  // Format output with carriage returns after a transmission pause
  if ((currentTime - lastTransmissionTime) > transmissionPaused)
  {
    if (transmissionEnded == false)
    {
      // Separate the transmissions somewhat in the serial monitor with CR's
      for (int cr=0; cr<2; cr++) Serial.println("");  // some carriage returns..
      
      // Finally set the flag to prevent continous carriage returns
      transmissionEnded = true;
    }
  }
}

void printString(char s)
{
  int col = 0;
 
    if (s < 32) return;
    char c = s - 32;
    memcpy_P(buffer, CH + 7*c, 7);
    m.writeSprite(col, 0, buffer);
    m.setColumn(col + buffer[0], 0);
    col += buffer[0] + 1;

}

end